Antenna Design and Calculations
RF Power Values
This document defines radio frequency (RF) power levels and the most common measure, the decibel (dB). This information can be very useful when you troubleshoot intermittent connectivity.
Power Level
The dB measures the power of a signal as a function of its ratio to another standardized value. The abbreviation dB is often combined with other abbreviations in order to represent the values that are compared. Here are two examples:
- dBm – The dB value is compared to 1 mW.
- dBw – The dB value is compared to 1 W.
You can calculate the power in dBs from this formula:
Power (in dB) = 10 * log10 (Signal/Reference)
This list defines the terms in the formula:
- log10 is logarithm base 10.
- Signal is the power of the signal (for example, 50 mW).
- Reference is the reference power (for example, 1 mW).
Here is an example. If you want to calculate the power in dB of 50 mW, apply the formula in order to get:
Power (in dB) = 10 * log10 (50/1) = 10 * log10 (50) = 10 * 1.7 = 17 dBm
Because decibels are ratios that compare two power levels, you can use simple math in order to manipulate the ratios for the design and assembly of networks. For example, you can apply this basic rule in order to calculate logarithms of large numbers:
log10 (A*B) = log10(A) + log10(B)
If you use the formula above, you can calculate the power of 50 mW in dBs in this way:
Power (in dB) = 10 * log10 (50) = 10 * log10 (5 * 10) = (10 * log10 (5)) + (10 * log10(10)) = 7 + 10 = 17 dBm
These are commonly used general rules:
| An Increase of: | A Decrease of: | Produces: |
| 3 dB | � | Double transmit power |
| 3 dB | Half transmit power | |
| 10 dB | 10 times the transmit power | |
| 10 dB | Divides transmit power by 10 | |
| 30 dB | 1000 times the transmit power | |
| 30 dB | Decreases transmit power 1000 times |
This table provides approximate dBm to mW values:
| dBm | mW |
| 0 | 1 |
| 1 | 1.25 |
| 2 | 1.56 |
| 3 | 2 |
| 4 | 2.5 |
| 5 | 3.12 |
| 6 | 4 |
| 7 | 5 |
| 8 | 6.25 |
| 9 | 8 |
| 10 | 10 |
| 11 | 12.5 |
| 12 | 16 |
| 13 | 20 |
| 14 | 25 |
| 15 | 32 |
| 16 | 40 |
| 17 | 50 |
| 18 | 64 |
| 19 | 80 |
| 20 | 100 |
| 21 | 128 |
| 22 | 160 |
| 23 | 200 |
| 24 | 256 |
| 25 | 320 |
| 26 | 400 |
| 27 | 512 |
| 28 | 640 |
| 29 | 800 |
| 30 | 1000 or 1 W |
Antennas
You can also use the dB abbreviation in order to describe the power level rating of antennas:
- dBi – For use with isotropic antennas.
Note: Isotropic antennas are theoretical antennas that transmit equal power density in all directions. They are used only as theoretical (mathematical) references. They do not exist in the real world.
- dBd – With reference to dipole antennas.
Isotropic antenna power is the ideal measurement to which antennas are compared. All FCC calculations use this measurement (dBi). Dipole antennas are more real-world antennas. While some antennas are rated in dBd, the majority use dBi.
The power rating difference between dBd and dBi is approximately 2.2—that is, 0 dBd = 2.2 dBi. Therefore, an antenna that is rated at 3 dBd is rated by the FCC (and Cisco) as 5.2 dBi.
Effective Isotropic Radiated Power
The radiated (transmitted) power is rated in either dBm or W. Power that comes off an antenna is measured as effective isotropic radiated power (EIRP). EIRP is the value that regulatory agencies, such as the FCC or European Telecommunications Standards Institute (ETSI), use to determine and measure power limits in applications such as 2.4-GHz or 5-GHz wireless equipment. In order to calculate EIRP, add the transmitter power (in dBm) to the antenna gain (in dBi) and subtract any cable losses (in dB).
| Part | Cisco Part Number | Power |
| A Cisco Aironet Bridge | AIR-BR350-A-K9 | 20 dBm |
| That uses a 50 foot antenna cable | AIR-CAB050LL-R | 3.35 dB loss |
| And a solid dish antenna | AIR-ANT3338 | 21 dBi gain |
| Has an EIRP of | 37.65 dBm |
Path Loss
The distance that a signal can be transmitted depends on several factors. The primary hardware factors that are involved are:
- Transmitter power
- Cable losses between the transmitter and its antenna
- Antenna gain of the transmitter
- Localization of the two antennas
This refers to how far apart the antennas are and if there are obstacles between them. Antennas that can see each other without any obstacles between them are in line of sight.
- Receiving antenna gain
- Cable losses between the receiver and its antenna
- Receiver sensitivity
Receiver sensitivity is defined as the minimum signal power level (in dBm or mW) that is necessary for the receiver to accurately decode a given signal. Because dBm is compared to 0 mW, 0 dBm is a relative point, much like 0 degrees is in temperature measurement. This table shows example values of receiver sensitivity:
| dBm | mW |
| 10 | 10 |
| 3 | 2 |
| 0 | 1 |
| -3 | 0.5 |
| -10 | 0.1 |
| -20 | 0.01 |
| -30 | 0.001 |
| -40 | 0.0001 |
| -50 | 0.00001 |
| -60 | 0.000001 |
| -70 | 0.0000001 |
The receiver sensitivity of the radios in Aironet products is -84 dBm or 0.000000004 mW.
Estimate Outdoor Ranges
Cisco has an Outdoor Bridge Range Calculation Utility to help determine what to expect from an outdoor wireless link. Because the outputs of the calculation utility are theoretical, it is helpful to have some guidelines on how to help counteract outside factors.
- For every increase of 6 dB, the coverage distance doubles.
- For every decrease of 6 dB, the coverage distance is cut in half.
In order to make these adjustments, choose antennas with higher (or lower) gain. Or use longer (or shorter) antenna cables.
Given that a pair of Aironet 350 Bridges (with 50 feet of cable that connects to a dish antenna) can span 18 miles, you can modify the theoretical performance of that installation:
- If you change to 100-foot cables instead of 50-foot (which adds 3 dB of loss on each end), the range drops to 9 miles.
- If you change the antenna to 13.5-dBi yagis instead of the dishes (which reduces gain by 14 dBi overall), the range drops to less than 4 miles.
Estimate Indoor Ranges
There is no antenna calculation utility for indoor links. Indoor RF propagation is different than outdoor propagation. However, there are some quick calculations that you can do in order to estimate performance.
- For every increase of 9 dB, the coverage area doubles.
- For every decrease of 9 dB, the coverage area is cut in half.
Consider the typical installation of an Aironet 340 Access Point (AP) with the rubber ducky 2.2-dBi dipole antenna. The radio is approximately 15 dBm. If you upgrade to a 350 AP and replace the rubber duckies with a high-gain omni-directional antenna that is rated at 5.2 dBi, the range nearly doubles. The increase in power from a 340 AP to a 350 AP is +5 dBi. And the antenna upgrade is +3 dBi, for a total of +8 dBi. This is close to the +9 dBi that are required to double the distance.
Source: http://www.zytrax.com/tech/wireless/calc.htm#db_calc
Power Budget Calculations
- mW to dBm = 10Log10(Watts) + 30
- feet to meters = .3048
- meters to feet = 3.28
- Calculator normalises all distances to kilometers and meters
- Connectors loss = 0.10 * square root (frequency in GHz)
Free Space Calculations
- Free space loss = 36.56 + 20Log10(Frequency) + 20Log10(Distance in miles)
- Calculator normalises all distances to miles
- Miles to Kilometers = 1.609
- Kilometers to miles = 0.621
Fresnel Zone Calculations
- Calculator normalises all distances to kilometers and meters
- Miles to Kilometers = 1.609
- Kilometers to miles = 0.621
- feet to meters = .3048
- meters to feet = 3.28
- 1st Fresnel Zone radius (Km) = 17.3 x Sqr root ((Obstacle Distance x (Total Link – Obstacle Distance)) / (Frequency in GHz x Total Link))
- 1st Fresnel Zone radius (miles) = 72.6 x Sqr root ((Obstacle Distance x (Total Link – Obstacle Distance)) / (Frequency in GHz x Total Link))
- Obstacle free radius = 0.6 x 1st Fresnel Zone radius
- Radius of nth Fresnel zone (meter) = sqr root ( (n x wave length x Obstacle distance x (Total Link – Obstacle Distance)) / Total Link )
- wave length (meters) = speed of light (299,792,458 m/s) / frequency in Hz
- Earth curvature calculation = (Total Link)^2 /(8 * effective earth radius)
- effective earth radius = 4/3 * Earth radius
- Earth radius = 3963 miles, 6378 Km
System Performance Calculations
- Calculator normalises all distances to miles and feet during calculations.
- Free space loss = 36.56 + 20Log10(Frequency) + 20Log10(Dist in miles)
- mW to dBm = 10Log10(milliWatts) + 30
- dBm to mW = 10^(dBm/10)
- RX Power = Margin – RX sensitivity
- Theoretical margin = TX power budget + RX power budget – free space loss
- SAD factor = Theoretical margin/TX power budget * 100 and shows the percentage of spare power on transmission.
dBm to Watts Calculations
- mW to dBm = 10Log10(Watts) + 30
- dBm to mW = 10^(dBm/10)